Previous Next

IGNITION TIMING

Timing

INSPECTION AND ADJUSTMENT

Piston Engines
EXCEPT 1988–89 626, MX-6 AND 929

NOTE: Most 1978 and later models require that the ignition timing be adjusted with the vacuum line connected to the distributor. Refer to the emission sticker (under the hood) to determine if the vacuum line is to be connected or disconnected and plugged. If the sticker is missing, see a dealer about obtaining a replacement with the proper calibrations for your vehicle.

  1. If required, disconnect and plug the distributor vacuum line. Though this is not required on most late model cars, it is needed on the 1986–87 626. On that model, be sure to disconnect BOTH vacuum lines and plug them.

    NOTE: A small pencil or old golf tee works well for this purpose.

    Fig. 1: Ignition timing marks — 1978–79 GLC

    Fig. 2: Ignition timing marks — 1980 GLC

    Fig. 3: Ignition timing marks — front wheel drive GLC

  2. Set the parking brake and block the front wheels. Put automatic transmission cars in Neutral.
  3. Turn off all electrical loads on all models (don't forget the heater fan). If the car has an electric fan, unplug the electrical connector.
  4. On the 1986–89 323 with electronic fuel injection, disconnect the black connector at the distributor.
  5. Start and run the engine until it reaches the normal operating temperature. Shut the engine OFF and connect a tachometer.
  6. Restart then engine, then check the engine idle speed and adjust if necessary. Shut the engine OFF..

    NOTE: Prior to starting the engine, clean off any grease or oil that will prevent seeing the timing marks on the crankshaft pulley. Mark the pulley notches with chalk or paint.

    Fig. 4: Ignition timing marks — 323

    Fig. 5: Ignition timing marks — 1983–85 626

    Fig. 6: Ignition timing marks — 1986–87 626

    Fig. 7: While aiming the timing light, rotate the distributor as necessary to align the designated timing marks

  7. Connect a timing light to the engine following the tool manufacturer's instructions. Start the engine and observe the timing by pointing the light at the timing marks on the crankshaft pulley.

    NOTE: If the car is equipped with an automatic transmission, check the emission sticker or tune-up specifications for transmission gear selections. Most models require the timing to be checked with the transmission in Drive, though some calibrations may require Neutral.

  8. If the timing is not correct, loosen the distributor mounting bolt and rotate the distributor as necessary to produce the correct timing mark alignment. Recheck the timing after tightening the lock bolt and readjust if necessary. Check the idle speed.

    NOTE: Some Canadian models require that the bullet connectors at the water temperature wiring be disconnected before timing the ignition; check the emission sticker for requirements.

  9. Reconnect the vacuum line(s) or bullet connectors, if applicable. Recheck the idle speed and readjust, if necessary.
1988–89 626 AND MX-6

NOTE: Prior to starting the engine, clean off any grease or oil that will prevent seeing the timing marks on the crankshaft pulley.

  1. Warm up the engine to normal operating temperature.
  2. Stop the engine and turn all electrical accessories to the off position.
  3. Connect a tachometer and timing light to the engine in accordance with the tool manufacturer's instructions.
  4. Connect a jumper wire from the test connector to a suitable ground.
  5. Start the engine and allow it to run at idle speed. Check and adjust the idle to specification, if necessary.
  6. On non-turbocharged engines, disconnect the two vacuum hoses from the vacuum control unit and plug them. Leave the test connector grounded.
  7. Aim the timing light at the crankshaft pulley and check that the yellow mark on the pulley is aligned with the mark on the timing belt cover.
  8. If the marks are not aligned, loosen the distributor bolt and move the distributor housing either clockwise or counterclockwise until the timing marks are properly aligned.
  9. Tighten the distributor bolt and connect the vacuum hoses to the control unit (non-turbocharged engines).
  10. Stop the engine, then disconnect the timing light and tachometer. Remove the jumper wire from the test connector.

    Fig. 8: Ground the test connector to check/adjust ignition timing — 626 and MX-6

    Fig. 9: Ignition timing marks — 1988–89 626 and MX-6

929

NOTE: Prior to starting the engine, clean off any grease or oil that will prevent seeing the timing marks on the crankshaft pulley.

  1. Warm up the engine to normal operating temperature. Check the idle speed and adjust as necessary.
  2. Stop the engine and turn all electrical accessories to the off position.
  3. Ground the green test connector pin with a jumper wire, as shown in the illustration.

    Fig. 10: Ground the test connector to check/adjust ignition timing — 929

    Fig. 11: Ignition timing marks — 929

  4. Start the engine and allow it to run at idle speed. Check and, if necessary, adjust the idle to specification.
  5. Connect a timing light to the No. 1 spark plug wire. If you are using a non-inductive timing light, the engine must first be stopped in order to wire the light inline with the No. 1 spark plug.

    NOTE: For accuracy and ease of use an inductive timing light is highly recommended on these vehicles.

  6. Check the timing using the light by illuminating the timing marks on the crankshaft pulley and the ignition timing scale.
  7. If the timing is not within specification, loosen the distributor bolt and rotate the distributor housing to adjust the timing.
  8. When the timing is correct, tighten the distributor bolt, then stop the engine.
  9. Disconnect the timing light and remove the jumper wire from the test connector.
Rotary Engines
1979 RX-7

NOTE: This timing procedure applies to all 1979 RX-7s EXCEPT those after chassis No. 522504 that are equipped with an automatic transmission. For 1979 RX-7s after chassis No. 522504 with an automatic transmission, see the procedure which immediately follows.

  1. Warm the engine up until it reaches operating temperature, then shut the engine OFF and connect a tachometer.
  2. On automatic transmission equipped vehicles, securely apply the handbrake, block the wheels, and put the car in Drive.

    Fig. 12: Timing marks on 1979–85 RX-7s — the arrow points to the LEADING mark, while the TRAILING mark is beside it

    Fig. 13: On early model 1979 RX-7s (and late models with MT), adjust the leading timing by rotating the distributor, then adjust the trailing timing by moving the vacuum unit (MT) or adjusting lever (AT) in or out

  3. Read the tachometer as for a conventional four cylinder engine to verify that the engine is running at its normal idle speed. If not, adjust idle speed to specification.
  4. Stop the engine and connect a timing light to the leading (lower) spark plug of the front rotor. Then, restart the engine. Aim the timing light at the pin on the front housing cover and observe the timing.
  5. If the timing pointer does not line up with the first (yellow) notch on the pulley, loosen the distributor locknut and rotate the distributor either way until timing is correct. Tighten the locknut and check that timing is still correct.
  6. Stop the engine and connect the timing light to the trailing (upper) spark plug of the front rotor. Start the engine (put automatic transmission equipped cars in Drive), and check the trailing timing. The timing pointer should line up with the second (red) notch in the pulley.
  7. If the trailing timing is not correct, loosen the vacuum unit attaching screws (manual transmission) or the adjusting lever attaching screws (automatic transmission), and move the vacuum unit (manual transmission) or adjusting lever (automatic transmission) in or out until the timing pointer lines up with the second mark on the pulley. Then, tighten the screws and recheck the timing.
1979 RX-7 WITH AUTOMATIC TRANSMISSION AFTER CHASSIS NO. 522504
  1. Warm the engine up until it reaches operating temperature, then shut the engine OFF and connect a tachometer.
  2. On automatic transmission equipped vehicles, securely apply the handbrake, block the wheels, and put the car in Drive.
  3. Read the tachometer as for a conventional four cylinder engine to verify that the engine is running at its normal idle speed. If not, adjust idle speed to specification.

    Fig. 14: On late model 1979 RX-7s (with AT), adjust the trailing timing by loosening the breaker base attaching screws, then loosen the external lever attaching screws and move the lever in or out

  4. Stop the engine and connect a timing light to the leading (lower) spark plug of the front rotor. Then, restart the engine. Aim the timing light at the pin on the front housing cover and observe the timing.
  5. If the timing pointer does not line up with the first (yellow) notch on the pulley, loosen the distributor locknut and rotate the distributor either way until timing is correct. Tighten the locknut and check that timing is still correct.
  6. Stop the engine and connect the timing light to the trailing (upper) spark plug of the front rotor. Start the engine (put automatic transmission equipped cars in Drive), and check the trailing timing. The timing pointer should line up with the second (red) notch in the pulley.
  7. To adjust the trailing timing, stop the engine and remove the distributor cap and rotor.
  8. Slightly loosen the breaker base attaching screws, then reinstall the rotor and distributor cap.
  9. Start the engine. Set the transmission selector lever in Drive and run the engine at idle speed. Move the external adjusting lever in or out until the timing pointer lines up with the second (red) mark on the pulley, then tighten the adjusting lever attaching screws.
  10. Stop the engine, remove the distributor cap and rotor, and tighten the two breaker base attaching screws.
  11. Install the rotor and cap, then recheck the trailing timing.
1980–85 RX-7
  1. Warm up the engine to normal operating temperature.
  2. Stop the engine and connect a tachometer.

    Fig. 15: For all 1980–85 RX-7s, adjust the leading timing by rotating the distributor, then adjust the trailing timing by moving the vacuum unit (MT) or adjusting lever (AT) in or out

  3. Connect a timing light to the wire of the leading (lower) spark plug on the front rotor.
  4. To check/adjust the leading timing:
    1. Start the engine and run it at the specified idle speed. Verify that the engine is running at its normal idle speed. If not, adjust idle speed to specification.
    2. Aim the light at the front cover timing indicator pin.
    3. If the timing pointer does not line up with the first (yellow) notch on the pulley, loosen the locknut and rotate the distributor until the timing is correct. Tighten the locknut and check that the timing is still correct.
  5. To check/adjust the trailing timing:
    1. Stop the engine and connect the timing light to the trailing (upper) spark plug on the front rotor. Start the engine, position the detent lever in Drive (AT vehicles), and check the trailing timing. The pointer should line up with the second (red) notch in the pulley.
    2. If the trailing timing is not correct, loosen the vacuum unit attaching screws on vehicles equipped with manual transmission or the adjusting lever attaching screws on vehicles equipped with automatic transmission. Move the vacuum unit or adjusting lever in or out until the timing pointer lines up with the second mark on the pulley, then tighten the screws and recheck the trailing timing.
1986–89 RX-7

1986–89 models do not use a distributor. Instead, ignition timing is adjusted by means of a crank angle sensor. The sensor is mounted in the front rotor housing and extends down towards the eccentric shaft. The sensor detects the angle of the eccentric shaft and feeds this information to the control unit in the form a reference signal. This, along with other input signals, allows the control unit to monitor the various engine operating conditions which it uses to calculate ignition timing.

  1. Warm up the engine to normal operating temperature.
  2. Stop the engine, connect a tachometer and turn off all accessories.

    Fig. 16: Ignition timing marks — 1986–89 RX-7

    Fig. 17: On 1986–89 RX-7s, ignition timing is adjusted by rotating the crank angle sensor

  3. Start the engine and verify that the engine is running at its normal idle speed. If not, adjust idle speed to specification.
  4. To Check/Adjust the leading timing:
    1. Connect a timing light to the lower spark plug wire from the front rotor.
    2. Aim the light at the pulley and verify the yellow pulley timing mark is aligned with the indicator pin.
    3. If the marks are not aligned, remove the rubber cap that covers the crank angle sensor adjusting bolt.
    4. Loosen the bolt and move the crank angle sensor to adjust the leading timing.
  5. To Check/Adjust the trailing timing:
    1. Connect the timing light to the upper spark plug wire from the front rotor.
    2. Check that the red pulley mark aligns with the indicator pin.
    3. If not, loosen the adjusting bolt and rotate the crank angle sensor to align the marks.
    4. Tighten the crank angle sensor adjusting bolt and install the rubber cap. Recheck the timing.

Previous Next